Search Results

Standard

Definitions for Macrostrain and Microstrain

2011-08-04

CURRENT

J932_201108

In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."

Standard

HIGH CARBON CAST STEEL SHOT

1994-07-01

HISTORICAL

J827_199407

This SAE Recommended Practice describes chemical composition, hardness, microstructure, and physical characteristic requirements for high carbon cast steel shot to be used for shot peening or blast cleaning operations.

Standard

HIGH-CARBON CAST-STEEL GRIT

1996-09-01

HISTORICAL

J1993_199609

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

HIGH-CARBON CAST-STEEL SHOT

1996-09-01

HISTORICAL

J827_199609

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

High-Carbon Cast-Steel Grit

2019-02-21

CURRENT

J1993_201902

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

High-Carbon Cast-Steel Grit

2013-10-16

HISTORICAL

J1993_201310

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

High-Carbon Cast-Steel Grit

2005-07-25

HISTORICAL

J1993_200507

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

Standard

High-Carbon Cast-Steel Shot

2005-07-25

HISTORICAL

J827_200507

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

High-Carbon Cast-Steel Shot

2013-10-16

HISTORICAL

J827_201310

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

High-Carbon Cast-Steel Shot

2019-10-31

CURRENT

J827_201910

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

Standard

METALLIC SHOT AND GRIT MECHANICAL TESTING

1996-04-01

HISTORICAL

J445_199604

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

METALLIC SHOT AND GRIT MECHANICAL TESTING

1984-08-01

HISTORICAL

J445_198408

This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

Manual on Shot Peening

1992-10-01

CURRENT

J808_199210

Not available.

Standard

Medical Device Shot Peening

2014-05-07

CURRENT

J3020_201405

This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.

Standard

Medical Device Shot Peening

2019-05-09

WIP

J3020

This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.

Standard

Metallic Shot and Grit Mechanical Testing

2022-05-04

CURRENT

J445_202205

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

Metallic Shot and Grit Mechanical Testing

2005-07-25

HISTORICAL

J445_200507

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

Metallic Shot and Grit Mechanical Testing

2013-08-21

HISTORICAL

J445_201308

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

Standard

PROCEDURES FOR USING STANDARD SHOT PEENING TEST STRIP

1984-01-01

HISTORICAL

J443_198401

This SAE Recommended Practice provides uniform procedures for using the standard shot peening test strips reported in SAE Standard J442, Test Strip, Holder and Gage for Shot Peening. Standard test strips are used to control repeatability of the shot peening machine operations, and to specify a desired result on a part. It is recommended that the standard test strip A be used for intensities that produce arc heights of 6A to 24A. For intensities below 6A, the standard N strip is recommended, and for intensities above 24A, the standard C strip is recommended. Shot peening is intended to induce surface compressive stresses in metal parts for the purpose of improving resistance to fatigue and stress corrosion cracking. Springs, axles, and aircraft landing gears are typical examples of such parts.

Standard

Procedures for Using Standard Shot Peening Almen Strip

2010-06-16

HISTORICAL

J443_201006

This SAE Recommended Practice provides uniform procedures for using the standard shot peening Almen strips reported in SAE J442. Standard Almen strips are used to establish saturation, determine intensity, monitor repeatability of the shot peening machine operations, and can be used to predict a desired result on a part. It is recommended that the standard Almen strip A be used for intensities that produce arc heights of 0.10 mm A (0.004 in A) to 0.60 mm A (0.024 in A). For intensities below 0.10 mm A (0.004 in A), the standard N strip is recommended, and for intensities above 0.60 mm A (0.024 in A), the standard C strip is recommended. Use of SAE 2597 Computer Generated Shot Peening Saturation Curves is voluntary, existing shot peening processes that do not take advantage of computer generated saturation curves need not be changed to meet the requirements listed herein.